How to Clean Grout That Has Turned Black: Mould and Stains
Grout is a small detail that makes a big difference. When it's clean, it frames your tiles. When it turns black, even a fresh bathroom or kitchen looks grimy.
The good news is that a good clean can lift surface dirt and mould. This guide shows you how to clean grout that has turned black, or just dull and discoloured, step by step. It covers why it happens, which cleaners are safe on grout, how to remove mould, and how to stop it coming back.
Quick answer: Open a window, run the extractor fan and put on rubber gloves. Scrub the grout with a nylon brush and a pH-neutral tile and grout cleaner, or a paste of bicarbonate of soda and water. Rinse with clean water and dry. For black mould, add goggles and a mask, and use a suitable mould and mildew remover as its label directs. Read the mould safety section below before starting. If mould keeps coming back, find and fix the cause of the damp, such as poor ventilation or a leak. Cleaning or new grout alone won't stop it.
Safety: Never mix cleaning products. UKHSA warns that bleach mixed with an acid, such as vinegar, lemon juice or a limescale remover, gives off chlorine. Bleach mixed with ammonia gives off chloramines. Breathing them in can irritate your lungs. Some mould removers contain bleach (sodium hypochlorite), so check the label and treat them the same way. Use one product at a time, rinse in between, wear gloves and keep the room aired.
Why does grout turn black?
Grout turns black when mould, dirt and moisture build up in it, leaving the lines dark and discoloured. It doesn't happen overnight. Ordinary grout is cement-based, with tiny pores that soak up water and grime.
Mould can darken shower grout. It needs damp, and a steamy bathroom gives it plenty.
Government guidance on damp and mould says condensation is one of the most common causes of damp and mould in homes. Moisture from showers builds up in the air if it can't escape. So a steamy shower with poor ventilation gives mould on grout a head start.
Dirt and grime do the rest. In kitchens, grease and food splashes settle into grout lines. In bathrooms, soap scum and shampoo add to it. On floors, feet grind dirt into the joints.
The wrong cleaning makes it worse. Mopping with dirty water just spreads grime back into floor grout. Kärcher, which makes floor cleaners, says to change the rinse water several times. And Mapei, which makes grout, says regular use of bleach or vinegar can discolour and weaken grout.
So why is your shower grout turning black? If the marks are spots or patches that come back soon after cleaning, think mould. Then check for poor ventilation, leaks or other causes of damp, and fix the cause as well as cleaning. If the grout is evenly grey and grubby, it's more likely to be dirt and soap.
Is it mould, dirt or something else?
Match what you see to the likely cause, then go to the section that deals with it.
| What you see | Likely cause | Where to look |
|---|---|---|
| Dark spots or patches in corners and along the tray, back soon after cleaning | Mould | "How to remove mould from grout in the shower" |
| Evenly grey, grubby grout across a wall | Dirt, soap scum and shampoo | "Step-by-step grout cleaning guide" |
| Dark lines on a floor | Dirt ground in by feet, or dirty rinse water | "How to clean black grout on floors and in kitchens" |
| Dark lines behind a hob or sink | Grease and food splashes | "How to clean black grout on floors and in kitchens" |
| White powder on dark grout | Efflorescence | "How to clean dark grout, and black grout that has turned white" |
| Black marks on the sealant along a bath or tray | Mould in the sealant | The last paragraph of "When to replace grout or sealant" |
Best methods to clean blackened grout
Start with the gentlest method, and only step up if you need to. Whatever you use, check the care guide for your tiles first, and test a small, hidden patch.
What you'll need
- Rubber gloves and goggles, because scrubbing can splash
- A nylon grout brush, or an old toothbrush for small areas
- A pH-neutral tile and grout cleaner (one that's neither acidic nor alkaline), or bicarbonate of soda
- A bucket of clean water and a sponge or cloth for rinsing
- A microfibre cloth to dry the tiles
- A mould and mildew remover, only if the black is mould
Natural cleaning solutions
Bicarbonate of soda helps scrub away dirt. It's slightly abrasive, so it helps lift grime out of the joints. Kärcher suggests mixing 3 parts bicarb with 1 part water into a thick paste. Work it into the grout with a brush, leave it for about 30 minutes, then rinse it off with warm water and a clean cloth.
Is bicarb and vinegar the best way to clean grout that has turned black? Not mixed together. The fizz is just the two reacting with each other, and the Royal Society of Chemistry explains that it stops once they're used up.
Use vinegar on grout only now and then, if at all. Mapei says the odd clean with vinegar shouldn't harm cement-based grout between ceramic or porcelain tiles. But regular use can discolour and weaken it. Lemon juice is acidic too, so the same goes for it.
Never use vinegar or lemon on marble or other natural stone, which acids can etch. And check your tiles' care guide first: Plumbworld's own tile guide rules out acidic cleaners on its tiles.
A steam cleaner can loosen stubborn dirt. Kärcher, which makes steam cleaners, suggests a detail nozzle with a small round brush, scrubbing each joint in turn, then wiping the loosened dirt away with a cloth. Check that your tiles and grout can take the heat first. Keep steam off silicone unless the sealant's maker allows it. Where permitted, Kärcher says to avoid both scrubbing and a power nozzle.
For more on what natural cleaners can and can't do, see our guide on how to clean a bathroom naturally. For mould, use a mould and mildew remover, as the next sections explain.
Chemical cleaning methods
Use a pH-neutral tile and grout cleaner for regular cleaning. Mapei recommends a neutral cleaner for routine care of tiles and grout.
For black mould, use a mould and mildew remover. Government guidance says to use mould and mildew products rather than bleach, for health and safety reasons. Choose one that suits your tiles and grout, and follow the label for how long to leave it.
Keep bleach for when you really need it. Mapei says grout should withstand the occasional use of diluted bleach, but regular use can discolour and weaken it. Only use bleach if your tile and grout care guides allow it. Follow its label for how much to dilute it, how long to leave it, what to wear and how to rinse it off.
Oxygen bleach powders are sold as stain removers. Only use one on grout if its label says it suits tiles and grout. Follow the label's mixing and contact times.
Shop-bought grout cleaners vary a lot. Some are acidic and made for limescale or cement haze, not mould. Kärcher warns that acidic cleaners attack cement joints over time. Its advice to wet joints first concerns acid cleaning. Follow your cleaner's label and your tiles' care guide, and keep these cleaners off shower trays and enclosure frames. Mira, which makes shower trays, warns that grout and tile cleaners can damage the tray and its waste.
Grout pens colour over stained grout rather than cleaning it. Clean the grout and let it dry fully first, then follow the pen's instructions. A pen won't remove mould, so treat any mould first.
Which grout cleaner should you use?
| Problem | Try this | Avoid |
|---|---|---|
| Grey, grubby grout | A pH-neutral tile and grout cleaner, or a bicarb paste, and a nylon brush | Wire brushes and metal scourers |
| Black mould spots | A mould and mildew remover that suits your tiles, following its label | Mixing it with any other cleaner |
| Dark or black-coloured grout | A soft brush, warm water and a pH-neutral cleaner | Regular bleach or vinegar, which can fade it |
| Marble or other natural stone | A cleaner the stone's supplier recommends | Vinegar, lemon and other acids |
| Sound grout that stays stained | A grout pen to recolour it, once any mould is treated | Covering mould without treating it |
Step-by-step grout cleaning guide
Follow these steps to clean grout that has turned black in the shower, or to clean grout lines on any wall or floor tiles.
- Prepare the area. Open a window and run the extractor fan. Put on gloves and goggles, and a mask if you're dealing with mould. Wipe loose dirt and hair off the tiles with a damp cloth.
- Choose your cleaner. Apply your chosen cleaner to the grout lines: a neutral grout cleaner, a bicarb paste, or a mould remover for mould.
- Let it sit. Leave it for the time on the product's label. Don't let it dry out on the grout.
- Scrub thoroughly. Work along each grout line with a nylon brush. Skip wire brushes and metal scourers, which could scratch the tile glaze.
- Rinse and repeat. Rinse with clean water, changing it often, so no cleaner or loosened dirt is left in the lines. Repeat on any stubborn patches.
- Dry completely. Dry the tiles and grout with a microfibre cloth, and leave the fan running so no moisture sits in the joints.
How to remove mould from grout in the shower
To get rid of black mould on grout, use a mould and mildew remover, then let the area dry completely. Government guidance on damp and mould says mould can be removed from hard surfaces with a suitable cleaning product.
Safety: Wear a mask, gloves and goggles, as the guidance advises, and follow the cleaner's safety instructions. Shut the bathroom door so spores don't spread, but open the window. Don't dry-brush or vacuum mould, because that puts spores into the air. Wash or throw away the cloth afterwards. The guidance says larger areas of mould should only be tackled by professionals. If you can't reach the area safely, or breathing in fumes or spores is a worry for you, ask someone else to help.
Mould is a health matter, not just a looks one. The guidance says damp and mould can cause coughs, wheezing and shortness of breath. People with health conditions, children and older adults are at greater risk. So deal with mould promptly.
Cleaning surface mould does not fix the cause of damp. The guidance warns that removing surface mould won't stop damp and mould coming back. Find and fix the cause too, such as poor ventilation or a leak. If mould has got deep into the grout, Kärcher says the only answer is to replace it.
If you rent in England, report damp and mould to your landlord. Our guide on how to remove black mould from your bathroom covers that, and mould on walls, ceilings and sealant as well.
How to clean dark grout, and black grout that has turned white
Grout that's meant to be black or dark grey needs gentler care, because strong cleaners can fade it. Scrub it with a soft brush, warm water and a pH-neutral grout cleaner. Mapei says regular bleach or vinegar can discolour grout, so keep both off.
Has your black grout turned white? ARDEX, which makes grout, says the most likely cause of grout turning white is efflorescence. That's a dry white powder left on the surface as water dries out of cement-based products.
ARDEX says efflorescence can be removed with a cleaner made for the job, and that using lots of water when cleaning makes it worse. So ask your grout's maker which treatment suits your grout and tiles. Limescale and soap scum can also leave a pale film on dark grout. Our guide on how to clean black bathroom fixtures has more on black tiles and black grout.
How to clean black grout on floors and in kitchens
Floor grout gets dirtier than wall grout, because feet grind dirt into the joints. Use the steps above, with a pH-neutral cleaner and a nylon brush. Then rinse the floor with clean water.
Kärcher says to change the rinse water several times, until no cleaner is left. Dirty water puts grime straight back into the grout. The steam method above works on floor joints too, if your tiles and grout can take the heat.
In kitchens, the dark lines are usually grease and food splashes. Warm water with a little washing-up liquid, a nylon brush and a rinse will usually lift them. Wipe spills up straight away, so they don't build up in the joints.
Preventing grout from turning black again
Keeping grout dry and clean helps it stay bright. Three habits do most of the work: wipe it down, air the room and protect the grout.
Regular cleaning routine
A quick wipe after each shower helps stop grime and moisture building up. Use a shower squeegee or a microfibre cloth to take the water off the tiles, as Kärcher suggests. In kitchens, wipe up spills and grease straight away.
Once a week, clean the tiles and grout with a pH-neutral cleaner. Every few weeks, give the grout lines a scrub with a soft brush so dirt can't settle in. ARDEX says a regular cleaning routine reduces mould on cement-based grout.
Proper ventilation and moisture control
Good ventilation helps stop grout going mouldy. Government guidance says bathrooms need good ventilation. That means an extractor fan that works and is powerful enough to clear the moisture from showers and baths. If mould keeps coming back even with a good fan, look for a leak or another cause of damp.
- Run the fan while you shower, then leave it running for at least 15 to 20 minutes afterwards, as Crosswater, which makes shower enclosures, advises. If there is no fan, open a window during the shower and leave it open afterwards.
- Keep the door shut while you shower, so the steam doesn't drift into cooler rooms. The government guidance advises closing internal doors when you shower or cook.
- Keep the fan working. Clean its grille now and then, with its power switched off at its isolator switch or the fuse box first, as our deep clean guide explains.
- Think about a humidistat fan. If people forget to switch the fan on, a humidistat extractor fan switches on by itself when the air gets damp.
A dehumidifier can help dry the air in a room with poor airflow, but it won't cure a leak or replace good ventilation.
No fan, or a weak one? Plumbworld sells a range of bathroom extractor fans. Fitting one in a bathroom is electrical work, so have a registered electrician do it. Our guide to bathroom ventilation explains your options.
Sealing grout for long-term protection
A grout sealer helps stop stains soaking in and lets dirt wipe off more easily, Mapei says. Seal cement-based grout once it's clean and completely dry. Apply the sealer with a small brush or applicator, so it coats the grout lines evenly. Then let it cure (set fully) before the shower gets wet. Follow the sealer's own drying times.
There are two main types. Penetrating sealers soak into the grout. Some leave its look unchanged; others deepen the colour. Topical sealers sit on top as a coating, wear off faster and need reapplying more often.
How often should you reseal? There's no set interval: it depends on wear and how you clean.
Tip: Mapei suggests a water drop test. Sprinkle a little water on the grout and wait a few minutes. If it soaks in quickly and darkens the grout, it's time to reseal.
Strong cleaners can make a penetrating sealer less effective, Mapei warns, so keep to a neutral cleaner.
When to replace grout or sealant
If your grout is beyond saving, replace it. Rake out and redo grout that's cracked or crumbling, or where mould has got deep inside. Sound grout that's just stained can be recoloured with a grout pen instead, once any mould is treated.
Safety: Raking out old grout makes dust. HSE lists mortar and concrete among the materials whose dust contains silica, which can harm your lungs when you breathe it in, and grout is cement-based. Keep dust down while you work, not just when you clean up. For a small hand-raking job, keep the working area damp and collect debris as you go. Wear goggles and a well-fitting FFP3 mask. HSE says not to dry sweep: use wet cleaning or a vacuum of dust class M or H. A tight-fitting mask only protects you if it seals to your face, and it won't seal over a beard or stubble. This guide covers raking out by hand only. If you cannot control the dust, use a tiler.
Choose a grout that suits your tiles and joint width and is made for wet areas, such as a wall tile grout with a mould inhibitor, from our adhesives and grout range. For floors, check that it is floor-rated, because wall grout is not automatically suitable. Our guide to replacing mouldy grout shows you how to remove and reapply it.
Black marks on the silicone sealant along the bath or tray are a separate job. If mould won't clean off the sealant, replace it with fresh silicone sealant suitable for baths and showers. Follow the sealant maker's preparation and curing instructions.
Consider installing bathroom wall panels
If you're tired of scrubbing grout, think about replacing your shower tiles with bathroom wall panels.
Panels cover a wall in a few large waterproof boards, so there are no grout lines to clean. Their smooth surface wipes clean. They're quicker to fit than tiles, and many can go over sound old tiles. Tile effect designs, like the one pictured below, suit modern and traditional bathrooms alike. Panels still need care, though: keep their sealed joints clean. If a joint fails, reseal it with the sealant the panel maker specifies. Multipanel specifies silicone; Fibo specifies an approved MS polymer sealant and says not to use silicone.
Not sure which to choose? Our guide to bathroom panels instead of tiles compares cost, fitting and cleaning.
Questions about cleaning black grout
What should you not use to clean grout?
Skip wire brushes and metal scourers, which could scratch the tiles. Don't use vinegar, lemon or bleach as everyday cleaners, because Mapei says regular use can weaken grout. Keep acids off natural stone. And never mix bleach with vinegar, limescale removers or ammonia.
Can you clean black grout without scrubbing?
Some mould removers are made to be sprayed on, left and wiped off. Astonish, for example, says its mould stain remover needs no scrubbing. Follow the product's label. A brush can help loosen everyday dirt in grout.
How do you get black grout stains off white tiles?
Wipe the tile faces with warm soapy water and a soft cloth, then dry them. If the black is in the grout lines, clean the grout as in the steps above. For a dark film left on new tiles after grouting, ask the grout's maker which haze remover suits your tiles.
How do you turn black grout white again?
Clean it first, with a pH-neutral cleaner or bicarb paste and a nylon brush, as in the steps above. Treat any mould with a mould and mildew remover. Sound grout that stays stained can be recoloured with a grout pen. Grout that is cracked, crumbling or mouldy deep inside needs replacing.
Can you use hydrogen peroxide on grout?
Kärcher says a 3% solution is enough to tackle mould spores on joints. It suggests laying soaked kitchen roll on the joint to keep the solution in contact, and rinsing it away with plenty of water after half an hour. Wear gloves and goggles, and try it on a hidden patch first.
Never mix it with a bleach-based mould remover. Hydrogen peroxide can react rapidly with bleach and release oxygen gas. Never combine them. Government guidance points to mould and mildew products, so use one of those if you're unsure.
How do professionals clean dirty grout?
They match the cleaner to the tile and the stain, because mould, rust and limescale need different products. They try it on a hidden patch first, mix it as the maker says, leave it for the time on the label, then rinse with plenty of clean water. Some use steam, as in the steam method above.
Ready to tackle black grout in your bathroom and kitchen?
Start with a nylon brush and a gentle cleaner, and step up only if you need to. If it's mould, a mould remover deals with what you can see, and fixing the damp stops it coming back. And if the grout is past saving, fresh grout or a set of wall panels gives you a clean start.
Start with a good clean this week, then get the fan running after every shower.
Find out more
- How to clean a shower enclosure: glass, frame and mouldy seals
- How to clean bathroom tiles: the tiles around the grout
- How to remove soap scum: the film that dulls tiles and glass
- How to seal a bath properly: when the sealant is mouldy too
- Tackling condensation in the home: the damp that feeds mould
Are you planning a new bathroom or kitchen makeover? Shop online with Plumbworld for guaranteed lowest prices on a wide range of premium brands, plus next day delivery options.
Sign up to our newsletter for the first time and get £10 off your order when you spend over £300. Plus, you'll discover all of Plumbworld's latest offers, newest product launches and advice from our experts.
Make sure you follow us on social media. Don't forget to share your bathroom or kitchen makeovers: tag us in your photos to be featured in our posts.
Find us at: Facebook | X (Twitter) | Instagram | TikTok | Pinterest
Don't forget to check out the rest of our blog for the latest bathroom and kitchen buying guides and advice from our experts.